-------------------------------------------------------------------------- DCC 3.1 released on 12.12.2023: * minor changes caused by DCU changes DCU 1.7 released on 12.12.2023: * fixed - order of DCU modules during initialisation * fixed - initialization after power-up * fixed - bug in low level function DCC_get_register ( called by DCCUSB_get_overload_state ) -------------------------------------------------------------------------- DCC 3.0 released on 05.05.2023: * minor changes caused by DCU changes DCU 1.6 released on 05.05.2023: * shows state of digital outputs (disabled or not) when overload appears * fixed - setting/loading/saving of controls names ( user defined) -------------------------------------------------------------------------- DCC 2.9 released on 05.12.2022: * new firmware version for Xilinx based DCCs - A2 -------------------------------------------------------------------------- DCC 2.8 & DCU 1.5 released on 02.06.2022: * support for new version of DCC-100 basing on Xilinx FPGA * fixed small problems while reconnecting DCU module after lost USB connection -------------------------------------------------------------------------- DCC 2.7 & DCU 1.4 released on 28.09.2021: * uses new CVI RTE v.19.0.0 instead of v.15.0.1 * uses new signed driver BH Driver v.147 (bhdrvr1470.sys)) for compatibility with the newest Windows versions stopped support for Windows 7 and 32-bit operating systems * minor changes on both DCC & DCU -------------------------------------------------------------------------- DCC 2.6 & DCU 1.3 released on 11.03.2021: * minor changes on both DCC & DCU -------------------------------------------------------------------------- DCC 2.5 & DCU 1.2 released on 22.09.2020: * minor changes on both DCC & DCU * 23.03.20 digital outputs of DCU modules can be reversed ( right mouse click on output button ->change output type->reverse output ) -------------------------------------------------------------------------- DCC 2.4 released on 27.01.2020: * changes required because of adding support for DCU USB module - no functional changes for DCC application * support added for DCU ( Detector Control Unit ) - * controlled by dcu_32(x64).exe application v.1.1 -------------------------------------------------------------------------- DCC 2.3 released on 15.11.2018: * Cooling is not dependent on Enable/Disable Outputs on new boards 9.01.18 * fixed: when trying to change Gain/HV (C1 & C3 ) to value bigger than limit, result is old value ( no change) -------------------------------------------------------------------------- DCC 2.2 released on 24.03.2017: * uses new CVI RTE v.15.0.1 instead of v.15.0.0 * uses new signed driver BH Driver v.123 (bhdrvr1230.sys) to solve BH drivers installation problems on computers with Windows 10 Anniversary Update and SecureBoot Enabled ( in BIOS) -------------------------------------------------------------------------- DCC 2.1 released on 06.12.2016: * workaround for DCC crash on exit when running on Windows 10 with Anniversary update -------------------------------------------------------------------------- DCC 2.0 released on 26.10.2015: * uses new CVI RTE v.15.0.0 instead of v.12.1.0 * uses new signed driver BH Driver v.12.0 (bhdrvr1200.sys) for compatibility with Windows 10 * minor bugs fixes -------------------------------------------------------------------------- DCC 1.7 released on 30.06.2014 : * recognizes DCC-110 module version ( no change in module functionality) * uses new signed BHDriver v.11.6 instead of Windriver 10.2 -------------------------------------------------------------------------- DCC 1.60 released on 12.12.2013: * command line switch -silent to enable DCC start without displaying error messagges - required to start DCC from SPCM application * Locking setup for connectors 1 and 3 is now separate for every module in use : -------------------------------------------------------------------------- DCC 1.51 released on 21.03.2011: * command line switch -mx to define number of modules in simulation mode * small bug fixings -------------------------------------------------------------------------- DCC 1.5 released on 09.09.2010: * uses new CVI RTE v.9.1.0 instead of v.9.0.1 * uses new Windriver 10.2 * prepared for using on Windows x64 versions * new naming convention for different .exe versions dcc_32.exe - 32-bit application to be used only on 32-bit Windows dcc_32x64.exe - 32-bit application to be used only on 64-bit Windows dcc_64.exe - 64-bit application to be used only on 64-bit Windows ( not ready yet) * Locking setup for connectors 1 and 3 possible : Menu bar -> Parameters -> Lock Connector1(3) Setup -------------------------------------------------------------------------- DCC 1.42 released on 09.09.2008: * Windriver 9.2.1 (or newer) is now standard driver for DCC modules * changes required for Windriver 9.2.1, * dcc.exe uses Windriver 9.2.1, dcc_w5.exe uses Windriver 5.2 -------------------------------------------------------------------------- DCC 1.41 released on 24.04.2008 : * uses new CVI RTE v.8.50 instead of v.8.01 * Module functionality not changed * better error messages for WinDriver initialization problems -------------------------------------------------------------------------- DCC 1.4 released on 10.08.2007 : * Module functionality not changed * changes required for Windriver 9.0, * dcc_w9.exe uses Windriver 9.0, dcc.exe uses old Windriver 5.2 -------------------------------------------------------------------------- DCC 1.3 released on 10.05.2007 : * Module functionality not changed * Changes on using PLX resources - for more flexible usage in PCI Cardbox -------------------------------------------------------------------------- DCC 1.23 released on 17.09.2004 : * Mouse movement on the gain sliders changes gain value immediately not only when mouse button was released -------------------------------------------------------------------------- DCC 1.22 released on 02.06.2003 : * Default path for saving auto.set and other program files can now be changed in Application Options window -------------------------------------------------------------------------- DCC 1.21 released on 05.09.2002 : * small bug in initialisation procedure fixed -------------------------------------------------------------------------- DCC 1.2 released on 09.08.2002 : * gain/HV limits (stored in DCC EEPROM) are added for better external device protection -------------------------------------------------------------------------- DCC 1.1 released on 08.03.2002 : * on overload gain/HV and +12V state can be changed